Vehicles
85 not categorized PORSCHE 911 SEAL KITCan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.95534990400
View/Change Diagram
From $28.60
Make a selection
$15.95
Make a selection RK968 When doing a belt service you may notice a little oil around the balance shafts or cam shaft. Do not ignore this! If the belts become oil soaked it could cost you an engine! So save time and money with our complete reseal kit! General Fitment968 1992-95944 1989-91 944 1985-88
$83.24
Make a selection PO930RBCKIT Rear; 2 required per vehicle
$48.91
Make a selection RK924 When doing a belt service you may notice a little oil around the balance shafts or cam shaft if so, do not ignore this! If the belts become oil soaked it could cost you an engine! So save time and money with our complete reseal kit General Fitment924 1980-85924 1976-79
$93.00
Make a selection PO930FBCKIT Front; 2 required per vehicle
$48.91
Make a selection 92835191900 Known as: repair kit / repair kit comprising: piston boot View/Change Diagram
$102.43
Make a selection FVD307955957 The kit consists of: oil strainer 955 307 403 01 seal 955 397 016 00 seal 955 325 443 00 seal 955 321 181 01 seal 955 321 379 00 16 spacer sleeves
$88.01
Make a selection 100103038TU997 Mahle 3.8 liter piston and cylinder conversion kit for 996/997 turbo / GT2 & GT2 rs - increased horsepower and torque.* - forged pistons with deeper, mirrored valve pockets with 23 mm wrist pin. - slip fit, steel (st52) cylinders. - piston pin bore is off center (deaxiert) for factory quiet operation. - 9.4:1 compression. - 102 mm bore. - piston rings installed directly on the pistons for ease of installation. - made in Germany by mahle gmbh. *please note: horsepower and torque gains depend on the software used, camshafts, crankshaft and other internal modifications. 700+ hp and torque can be achieved with use of these pistons and cylinders with a proper engine build and software. Contact your sales person for ...(choose a part on the right to read more) General Fitment911 TURBO/GT2 2001-05911 TURBO/GT2 2007-09
$14,654.60
Make a selection 90110090203 You cannot rebuild without this critical kit! Every gasket and seal you could imagine for a thorough job. Other kits available for larger engine displacements. View/Change Diagram
$332.71
Make a selection 106084 There are not many warning signs of an impending ims failure short of a “death rattle” that occurs as the bearing fails and comes apart. These kits replace the factory sealed bearing with a new, severe duty custom ceramic hybrid roller ball bearing for reduced friction and superior performance in poorly lubricated operating conditions and replaces the factory ims flange hub, bearing support, and fastener with a stronger, revised billet chromoly assembly. The center bearing support also receives an increase in size and no longer is cut for the o-ring that keep engine oil from leaking out of the engine - we have relocated the o-ring to the ims hub flange for added strength to the center stud & bearing support...(choose a part on the right to read more) General FitmentBOXSTER 2005-08BOXSTER 1997-04 911 1998-05 911 1987-89
$899.99
Make a selection AP996TT105 Agency power has just given Porsche 996tt owners another way to get an easy 20 bolt-on horsepower with this new big mouth plenum and throttle body kit. agency power set out to engineer and design a plenum that was functional, did not require additional tuning, and simply. Made power! the plenum is 6061 aluminum that retains the same shape as the factory t pipe. the reason to keep a standard t shape is that the engine works off of pulses. just like how Porsche designed, agency power kept this design and simply improved the restriction, the throttle body. the factory throttle body inlet size is 76mm that then jumps up to a 78mm id plastic plenum. General Fitment911 TURBO/GT2 2001-05
$850.95
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |